Chemistry · Kidato 3

Topic 8: extractions of metals

Dakika 26 za kusoma ·

Yaliyomo

Occurrence And Location Of Metals In Tanzania

Locations of Important Metal Ores in Tanzania

Most metals are found naturally as compounds called minerals.

Rocks are made up of crystals of metals.

An ore is a rock that contains enough of a metal compound for it to be worth extracting the metal.

The most common ores contain oxides. An example is the ore haematite, which contains iron (III) oxide.

Some ores contain other metal compounds. Malachite contains copper (II) carbonate.

Tanzania is blessed with an assortment of minerals.

The minerals found in Tanzania include

  • Gold, which is found in Geita (Mwanza), Kahama (Shinyanga), Nyamongo, Buhemba and Majimoto (Mara), and Nzega (Tabora).
  • Iron, which occurs in large deposits at Liganga in Ludewa (Iringa).
  • Copper, which is found in Mpanda (Rukwa).
  • Sodium, which occurs in several forms:
  • as sodium chloride at Uvinza (Kigoma)
  • as soda ash (Na2CO3) in Lake Natron
  • as rock salt in Kilwa
  • as a dissolved salt (NaCl) in sea water

The Abundances of Metals in the Earth's Crust

Metals occur in the sea and in the earth.

The form in which they occur depends on their reactivity.

The most reactive metals are extracted from the sea. Calcium is extracted from limestone, chalk and marble in the sea.

Metals of medium reactivity are found in the earth in the form of oxides and sulphides. Examples are aluminium, zinc, iron and tin.

The least reactive metals, such as silver and gold, occur as free uncombined elements.

We obtain most of the metals we use from the earth's crust.

The majority of metals are too reactive to exist as natural elements. They are found as compounds in ores.

The chief ores, in order of their economic importance, are

  • oxides
  • sulphides
  • chlorides
  • carbonates

The most common metal is aluminium. It makes about 7.8% of the earth's crust.

Iron follows, with approximately 4.5%.

The other metals are

  • calcium (3.5%)
  • sodium (2.5%)
  • potassium (2.5%)
  • magnesium (2.8%)

The remaining metals make about 3% of the earth's crust.

Chemical Properties Of Metals

The Difference between Physical and Chemical Strengths of Metals

Metals have a greater tendency to lose electrons. When they do, they go into solution as ions.

A metal can therefore be defined as an element which can ionize by electron loss.

The number of electrons lost per atom is the valency of the metal. The ion carries an equal number of positive charges. For example:

  • Na → Na+ + e– (univalent)
  • Mg → Mg2+ + 2e– (divalent)
  • Al → Al3+ + 3e– (trivalent)

The following are important chemical properties of metals

  • They react with oxygen to form oxides. For example, magnesium burns in air to form magnesium oxide. Metal oxides are bases. This means they react with water to form an alkaline solution, and with acids to form salts.
  • Metals form positive ions when they ionize. In the equations above, ionization of sodium, magnesium and aluminium gave Na+, Mg2+ and Al3+ ions respectively. There is one exception. Hydrogen is a non-metal which forms positive ions in solution, H+. This is the only exception in this case.

Physical strength is different from chemical strength.

Physical strength is the tensile strength of the metal. Some metals have high tensile strengths, like iron, copper and aluminium. Other metals, like sodium and potassium, have low tensile strengths.

Chemical strength is the reactivity of the metal. Sodium and potassium have very low tensile strengths, but they are the strongest metals chemically.

Sodium

Sodium and potassium are very weak physically.

Sodium is a very soft metal and can be cut easily with a knife. It melts at 98 °C.

It is so light that it floats on water. But it reacts immediately with the water and forms an alkaline solution.

When freshly cut, it has a silvery lustre. It rapidly tarnishes because it reacts with atmospheric carbon dioxide and moisture.

Potassium

Potassium is a white metal with lustre. It melts at 63 °C.

Like sodium, potassium is a very light metal. It also floats on water, and reacts with it to form an alkaline solution.

Sodium and potassium chemically

Sodium and potassium are among the strongest metals chemically.

These metals are very reactive and are always found combined with other elements. They are so reactive that they will combine with any non-metal nearby.

They never occur free in nature.

Both are so reactive that they have to be stored under oil. This prevents them from coming into contact with water or air.

The compounds of sodium and potassium are quite abundant in nature.

The reactivity and tensile strengths of some metals

  • Calcium: Calcium is among a group of metals that are too reactive to occur in the free state. It occurs mainly as carbonate, sulphate, fluoride and silicate. It is a soft, greyish metal. Compared with potassium and sodium, it has a lower tensile strength and a high density.
  • Iron: Iron is a typical metal. Its density is 7.87. It melts at 1530 °C. Iron is a moderately reactive metal. It reacts with excess steam at red heat to produce triiron tetraoxide.
  • Copper: Copper is a less reactive metal. It is a red-brown metal with a lustre. It can be polished. Its tensile strength is fairly high.

When heated in air, copper forms a layer of black copper (II) oxide on the surface

2Cu(s) + O2(g) → 2CuO(s)

Copper reacts with hot concentrated sulphuric acid to form copper (II) sulphate and liberate sulphur dioxide:

Cu(s) + 2H2SO4(aq) → CuSO4(aq) + 2H2O(l) + SO2(g)

The table below compares the tensile strengths of calcium, iron and copper metals.

Tensile Strengths, Densities And Melting Points Of Calcium, Iron And Copper

The table below compares calcium, copper and iron.

Calcium

  • Tensile strength: Low
  • Melting point: 850 °C
  • Density: 1.55 g cm-3

Copper

  • Tensile strength: Fairly high
  • Melting point: 1080 °C
  • Density: 8.95 g cm-3

Iron

  • Tensile strength: High
  • Melting point: 1535 °C
  • Density: 7.9 g cm-3

The Reducing Power Of Different Metals

Comparing the reducing power of different metals

As we learned earlier, metals tend to lose electrons during chemical reactions. This process of losing electrons is called oxidation.

Metals normally lose electrons to non-metals. The non-metals accept those electrons.

Therefore, metals are said to be electron donors. Non-metals are electron acceptors.

Metals can be called reducing agents. This is because they donate electrons. When non-metals accept these electrons, their oxidation numbers become lower.

Non-metals are called oxidizing agents. They oxidize the metallic atoms, that is, they increase the oxidation number of metallic atoms by accepting the electrons donated by metals.

Why metals differ in losing electrons

Metals differ in how easily they lose electrons. This depends on their electronic configurations.

Only the outer electron(s) take part in a chemical reaction.

The nucleus of an atom is positively charged. It attracts the electrons towards itself. This makes the electrons difficult to remove from their shells.

The further the electrons are from the central nucleus, the easier it is to remove them from their shells. The closer they are, the harder it is to remove them.

Therefore, atoms with larger atomic radii donate their electrons more easily than atoms with small atomic radii.

Example: sodium and potassium

Compare the electronic configuration of sodium (2:8:1) with that of potassium (2:8:8:1).

Sodium ionizes by losing one electron from its outer shell. It then attains the structure of the nearest noble gas (2:8).

Potassium also ionizes by losing one electron from its outer shell. It then attains the noble gas structure 2:8:8.

In which case is it easier to remove the electron, and why?

It is easier to remove the electron from the outer shell of potassium than from sodium. This is because the atomic radius of potassium is much larger than that of sodium.

(Note: the source text wrote "calcium" here, but the comparison is between potassium and sodium.)

In potassium, the outer electron is held more loosely by the central nucleus. So it is easy to remove from its shell.

This is true because the ability of the nucleus to hold electrons firmly depends on the distance of the electrons from the nucleus.

Strong and weak reducing agents

Metals that release electrons more readily are strong reducing agents. Metals that release their electrons least readily are weaker reducing agents.

For example, potassium (2:8:8:1) is a stronger reducing agent than sodium (2:8:1).

Stable structures

When atoms of elements lose electrons from their outermost shells, they obtain octet or doublet structures. They then become chemically stable.

It is not easy to remove electron(s) from such stable noble gas structures by ordinary chemical means.

Definition of reducing power

The reducing power of a metal is its readiness to release electrons from its outer shell.

Metals whose atoms release electrons more readily have high reducing powers. Metals whose atoms do not release electrons readily have lower reducing powers.

Reactivity Series Of Metals

The reactivity series means arranging or listing metals in order of reactivity.

The reactivity series is obtained by considering three things

  • the action of air on the metals
  • the action of water on the metals
  • the action of acids on the metals

It also considers how easily the oxides of these metals can be reduced.

Consider the table of reactivity series (Table 8.2). In it, the metals are arranged in order of reactivity.

The metals fall into three groups

  • The oxides of the first group of five metals cannot be reduced by carbon.
  • The second group of three metals can react with acids, displacing hydrogen.
  • The third and last group has the least reactive metals.

The series also shows the inverse order in which the elements were isolated.

Metals low in the series, such as gold, silver and lead, have been known since early times.

Metals high in the series proved very difficult to isolate.

Davy's work on electrolysis led to the isolation of potassium, sodium, calcium, magnesium and aluminium. This happened over a period of years. It began in 1807, when Davy isolated potassium and sodium. It ended at about 1850, when aluminium was isolated.

The Reactivity Series Of Metals

Metals low down in the series are often found as free elements. They may also be obtained from ores, because the amount found as free metal is not enough for industrial purposes.

Gold is the last element in the series. It is found and mined almost entirely as the free element.

Generally, these relatively unreactive metals have the most uses. Iron and copper, for example, are found in many household and everyday objects.

Metals higher up in the series are more reactive than those lower down. A metal higher up in the series will displace a metal lower down from a solution of one of its salts. For example, iron will displace copper from its salt.

Fe(s) + CuSO4(aq) → Cu(s) + FeSO4(aq)

Zinc and iron will displace hydrogen from dilute acids such as dilute hydrochloric acid or dilute sulphuric acid.

Zn(s) + 2HCl(aq) → ZnCl2(aq) + H2(g)

Fe(s) + H2SO4(aq) → FeSO4(aq) + H2(g)

Copper has no reaction with dilute sulphuric acid or dilute hydrochloric acid. With hot concentrated sulphuric acid, sulphur dioxide is liberated and copper (II) sulphate is formed.

Cu(s) + 2H2SO4(l) → CuSO4(aq) + 2H2O(l) + SO2(g)

Useful Things To Remember About The Reactivity Series

  • The more reactive the metal, the more compounds it forms. So only copper, silver and gold are ever found as free elements in the earth's crust. The other metals are always found as compounds.
  • When a metal reacts, it gives up electrons to form ions. The more reactive the metal, the more easily it gives up electrons.
  • The more reactive the metal, the more stable its compounds are. Stable means difficult to break down. For example, when you heat sodium nitrate you get sodium nitrite:

2NaNO3(s) → 2NaNO2(s) + O2(g)

But copper (II) nitrate breaks down further, to the oxide, giving off nitrogen dioxide

2Cu(NO3)2(s) → 2CuO(s) + 4NO2(g) + O2(g)

  • The more reactive the metal, the more difficult it is to extract from its compounds, since the compounds are stable. For the most reactive metals, you will need the toughest method of extraction: electrolysis.
  • The less reactive metals have been known and used since ancient times, because they are the easiest to extract.
  • If you stand two metals in an electrolyte and join them with a copper wire, electrons will flow from the more reactive metal to the less reactive one.

Extraction Of Metals By Electrolytic Reduction

The criteria for the choice of the best method of extracting a metal from its ore

Most metals are found naturally in compounds called ores. The metals are obtained from the ores by a process called extraction. Extraction means separating the metal from the minerals in the ore.

A few metals are found "native". This means they are uncombined with other elements. Silver and gold are examples.

To extract metals from ores containing minerals, a chemical reaction must be used to separate the metal from the other elements. The best method of extraction depends on the chemical reactivity of the metal to be extracted.

Most ores contain metal oxides. To extract the metal, oxygen must be removed from the oxide. This reaction is called reduction.

The metal is always the most electropositive part of an ore, so it has a positive oxidation state. Therefore, forming the free metal from its ore is always a reduction.

Mn+ + ne– → Mo

Very reactive metals like sodium and potassium are strongly bonded in their ores. The more reactive the metal, the more stable its compounds are. More energy is needed to break the bond between the metal and oxygen.

Therefore, extracting these metals needs a strong method of reduction: electrolysis (or electrolytic reduction).

Hence, metals at the top of the reactivity series are obtained from their ores by electrolysis (electrolytic reduction).

Electrolysis is a more expensive process than reduction with carbon or carbon monoxide. However, it is the only economic way to obtain metals such as aluminium.

For less reactive metals in the middle of the reactivity series, oxygen can be removed by chemical reduction with carbon or carbon monoxide. This method is used for metals such as zinc, iron and copper, as shown in table 8.3.

The least reactive metals such as copper, silver and gold may be found in the uncombined state.

Methods Of Extraction Of Different Metals From Their Ores

Electrolysis

  • Potassium
  • Sodium
  • Calcium
  • Magnesium
  • Aluminium

Chemical reduction with carbon or carbon monoxide

  • Zinc
  • Iron
  • Lead

Roasting in air

  • Copper

Occur naturally as elements

  • Silver
  • Gold

Stages Of The Extraction Of Moderately Reactive Metals

There are four main stages in the extraction of moderately reactive metals

  1. Mining and concentration of the ore
  2. Roasting in air
  3. Reduction of oxides to metals
  4. Purifying the metal

Mining and concentration of the ore

Mining is just the first step. The ore must then be decomposed to give the metal. This is called extraction.

The unwanted rock material in the ore is called gangue. The ore is treated to remove as much gangue as possible. For example:

  • Crushing and washing. The ore is broken into small pieces, which are then ground to a fine powder. Then it is either dropped into water, where the fragments containing the metal sink faster, or jets of air are blown at it, where the lighter waste material is carried to one side.
  • Froth flotation. This method is used with sulphide ores (e.g. CuS or ZnS). The ore is powdered, fed into water tanks and made into a slurry with water. Then "frothing" chemicals (a suitable oil) are added. Sulphides are attracted to these chemicals. When air is blown through the slurry, froth rises to the top of the tank carrying the metal sulphides with it. They are skimmed off and dried. The gangue sinks.
  • Magnetic separation. Iron ore can be separated from other material in the crushed ore by using an electromagnet.

Roasting in air

Some ores occur as sulphides or carbonates of the metal. The concentrated ore is heated (roasted) in air to convert it into an oxide. For example:

  1. 2PbS(s) + 3O2(g) → 2PbO(s) + 2SO2(g)
  2. 2ZnS(s) + 3O2(g) → 2ZnO(s) + 2SO2(g)
  3. ZnCO3(s) → ZnO(s) + CO2(g)

It is usual to convert sulphides and carbonates into oxides before reduction, because oxides are more easily and efficiently reduced than sulphides.

The oxides from roasting the sulphides or carbonates in air are then reduced chemically with carbon or carbon monoxide.

Most copper is extracted from copper pyrites, CuFeS2. The ore is roasted in a limited supply of air to produce copper (I) sulphide:

2CuFeS2(s) + 4O2(g) → Cu2S(s) + 3SO2(g) + 2FeO(s)

The copper (I) sulphide is then reduced to copper by heating in air

Cu2S(s) + O2(g) → 2Cu(s) + SO2(g)

The copper produced by this method is never pure. If it is to be used for electrical wiring, it must be refined (purified) by electrolysis.

Reduction of oxides to metals

This is another important stage in the extraction of a metal. The roasted ore must now be reduced to the respective metals.

Reduction occurs at a very high temperature. The materials used for reduction are mainly carbon or carbon monoxide. Thus:

Fe2O3(s) + 3CO(g) → 2Fe(l) + 3CO2(g)

ZnO(s) + C(s) → Zn(s) + CO(g)

Purification (Refining)

Very often, the product of the reduction process is not pure. It has to be purified before it is put into use. Purification is done in a number of ways, which include:

  • Electrolysis: Electrolysis is used to produce a pure metal directly from its molten compounds. Copper and zinc are examples of metals purified by electrolysis. Copper produced on a large scale is purified by electrolysis. This process is often called copper refining.
  • Oxidation: The molten crude metal is exposed to hot air in a furnace. The impurities in the crude metal are oxidized by oxygen from the air. They escape as vapour or form a scum over the molten metal, which is then removed by skimming. This method is used only when the impurities have a greater affinity for oxygen than the metal has. It is applied in the manufacture of steel from pig iron and in the purification of tin and lead.
  • Distillation: The crude metal is heated in a furnace until the pure metal evaporates, leaving the impurities behind. The vapour is then collected and condensed in a separate chamber. This method is an integral part of the extraction of zinc, cadmium and mercury. A further distillation, usually in vacuum, gives a very pure product.
  • Formation of carbonyls: Very pure nickel and iron are made by forming their volatile carbonyls, which are then decomposed by heating.
  • Zone refining: This recently developed method is used to produce silicon and germanium of extreme purity. A small high-frequency induction furnace is placed round one end of a long rod of the metal, and a thin cross-section of the metal is melted. The furnace is then moved slowly along the rod. Pure crystals of the metal separate from the melting metal, but impurities remain in the liquid and are carried along to the other end.

The Extraction Of Sodium From Its Ore

Alkali metals are strong reducing agents. They cannot be extracted by chemical reduction of their oxides or other compounds. The only possible method of extracting them is electrolysis of their fused chlorides.

Sodium is extracted industrially by electrolysis of either fused sodium hydroxide (Castner's process) or fused sodium chloride (Down's process). In Down's process, sodium chloride is electrolysed in the molten condition.

Electrolysis of sodium chloride by Down's process

In this case, fused sodium chloride is used. The melting point of sodium chloride is high (about 800°C). So calcium chloride is added to lower the melting point to about 600°C and thus save electrical power.

The composition of the electrolyte is 40% sodium chloride and 60% calcium chloride.

The Down's cell (figure 8.1) used for the extraction of sodium consists of an iron box. A circular carbon anode rises through the bottom of the box. A ring-shaped iron cathode surrounds this carbon anode. The cathode is enclosed in an iron gauze diaphragm, which also separates the two electrodes.

At 600°C, the sodium and chlorine produced would react violently if they came into contact. The diaphragm around the anode keeps the two products apart and prevents this.

During electrolysis, chlorine is liberated at the anode and escapes via the hood.

Sodium is liberated at the cathode. It collects in the inverted trough placed over the cathode, rises up the pipe, and overflows into the storage tank. It is tapped off from the tank through the iron vessel.

The sodium metal is collected upwards in the Down's cell because of its low density, which makes it float over the mixture.

The sodium metal from the Down's cell contains some calcium, which is also formed through electrolysis. The calcium crystallizes when the mixture cools, and a relatively pure sodium metal is obtained.

The Down'S Cell

Fused sodium chloride produces Na+ and Cl– ions. The Na+ ions move to the cathode. The Cl– ions move to the anode.

The reactions at the electrodes are as follows

  • At the cathode: Na+(l) + e– → Na(s). This is a reduction process.
  • At the anode: 2Cl–(l) → Cl2(g) + 2e–. This is an oxidation process.

Chlorine gas is therefore formed at the anode. Sodium metal is produced at the cathode.

The overall reaction is

2NaCl(l) → 2Na(s) + Cl2(g)

Chlorine is a valuable by-product of this decomposition process.

Extraction Of Metals By Chemical Reduction

The Extraction of Iron from its Ore

Iron is second only to aluminium as the most abundant metal in the earth's crust.

The chief ores of iron are

  • Haematite. It is an impure iron (III) oxide, Fe2O3. It contains about 70% of iron.
  • Magnetite (or magnetic iron ore). It is triiron tetraoxide, Fe3O4. It contains 72.4% of iron.
  • Spathic iron ore. It is iron (II) carbonate, FeCO3.

Iron also occurs as limonite, Fe2O3.xH2O. It also occurs as the sulphide in iron pyrites, FeS2.

Iron pyrite is abundant in the earth's crust. However, it is not used as a source of iron. It is mainly used in the production of sulphuric acid.

To extract iron, three substances are needed

  1. Iron ore: The chief ore is haematite. It is mainly iron (III) oxide, Fe2O3, mixed with sand.
  2. Limestone: This is mainly calcium carbonate, CaCO3.
  3. Coke: This is made from coal. It is almost pure carbon.

The Extraction Of Iron In A Blast Furnace

Before going into the blast furnace, all forms of iron ore must be converted to the oxide, Fe2O3. This is done by roasting in air.

4FeCO3(s) + O2(g) → 2Fe2O3(s) + 4CO2(g)

4FeS2(s) + 11O2(g) → 2Fe2O3(s) + 8SO2(g)

Iron ore, coke and limestone are mixed together. The mixture is called charge.

The charge is put into a tall tower called a blast furnace (figure 8.2). The charge is fed in continuously from the top.

At the bottom of the furnace, hot air is blasted in through several pipes. These pipes are known as tuyeres.

A well at the bottom of the furnace holds the molten iron and slag. They stay there until they can be run off.

Reactions that occur in the furnace

  • At the bottom of the furnace, the temperature is the highest. Air attacks the coke to produce carbon dioxide.

C(s) + O2(g) → CO2(g)

  • In the middle of the furnace, the rising carbon dioxide gas is reduced by more coke. This produces carbon monoxide.

C(s) + CO2(g) → 2CO(g)

  • At the top of the furnace, carbon monoxide reduces iron (III) oxide to metal.

Fe2O3(s) + 3CO(g) → 2Fe(s) + 3CO2(g)

The molten iron trickles down the furnace and gathers at the bottom.

From time to time, the molten iron is tapped off. It is run into moulds (or containers). There it cools into long bars about 1 metre long and 10 cm in diameter. At this stage it is called 'cast iron' or 'pig iron'.

The hot waste gases are mainly nitrogen and oxides of carbon. They escape from the top of the furnace. They are used to heat the incoming air. This helps to reduce the energy costs of the process.

The Blast Furnace: Action Of Limestone

The limestone is put in together with the ore. At the high temperature, it first decomposes to form calcium oxide.

CaCO3(s) → CaO(s) + CO2(g)

The main impurity in iron ore is sand. Sand is made of silicon dioxide (SiO2). It reacts with calcium oxide to form calcium silicate.

CaO(s) + SiO2(s) → CaSiO3(l)

The calcium silicate is a liquid. It falls to the bottom of the furnace. This liquid is called slag. It floats on the molten iron because it is less dense than the iron. It is tapped off separately.

Slag is a useful by-product. It is used for

  • making roads
  • production of cement
  • use as a fertilizer

Environmental Consideration

Environmental Destruction Caused By Extraction Of Metals

Learning aim: to identify environmental destruction caused by extraction of metals.

Mining and mineral extraction are important for economic development and for general human welfare.

Without mining, we would have no cars, computers, handsets, washing machines or other equipment. We use this equipment to simplify our work and so improve the quality of our lives.

However, mining can cause many environmental problems.

The following are some of the environmental problems caused by mining

Land subsidence (sagging)

Holes created by underground mining cause the land to sink (or subside).

This happens because the holes underneath the ground cause an imbalance in the weight of the soil above.

This may severely damage buildings and other infrastructure such as roads, railway tracks and so forth.

Poisonous substances

Poisonous compounds are found in many ores. Examples are compounds of lead, cadmium and arsenic.

These may be washed into the soil and streams because of the mining process.

If they reach the water, they can kill fish and plant life. They can also end up in your food.

The gold extraction process makes use of mercury.

If untreated effluent from the gold mine is directed to nearby rivers or streams, the metals may end up in fish. These fish might be someone's food.

Eating such fish can result in brain damage, because of the mercury it contains.

Large volume of waste

Large-scale mining operations inevitably produce a great deal of waste.

This waste includes earth from the soil and gangue. It also includes the toxic chemicals added to the ore to help metal extraction.

The waste material gets washed into streams and rivers.

The sediment that builds up blocks rivers and changes their routes.

This sediment is a source of pollutants to natural water systems.

Noise and dust

Mining activities produce a lot of noise and dust.

Noise and dust can be caused by haulage trucks, rock blasting and crushing, drilling operations and heavy traffic.

Everything for miles around the mine may get covered with dust.

Big holes in the ground

Mineral extraction leads to the boring of deep holes through the ground while searching for rich ores.

Huge amounts of rock are dug up to get a small amount of ore. For example, 1000 tonnes of rock may produce just 5 tonnes of copper.

This leaves huge scars on the landscape if the opencast method is used.

It leaves huge holes underground if underground mining is used.

Great heaps of earth material

Unwanted rock material is left after the metal has been extracted from the ore. It gets heaped up in tips.

These tips are unsightly.

They can be unstable and therefore dangerous.

During heavy rains, a landslide is likely to occur. This is a catastrophe that often results in loss of life and destruction of property.

Soil erosion

Before mining is carried out, the natural vegetation on or around the mining site is usually cleared. This gives enough room for mining activities.

Removing the vegetation cover leaves the soil bare. The soil is then susceptible to erosion.

Air pollution

Large-scale mineral extraction produces gases such as sulphur dioxide, carbon dioxide and other bad gases. These are emitted into the atmosphere.

These gases may bring about the greenhouse effect and even cause acid rain.

Intervention Measures To Rectify Environmental Destruction

Learning aim: to suggest intervention measures to rectify environmental destruction.

Different measures are taken to check the environmental degradation (problems) caused by mining activities.

The following are some remedy measures taken to prevent such environmental destruction

  • Governments are getting tougher with mining companies about damage to the environment. Sadly, in developing countries like Tanzania, where much mining takes place, laws may be less strict.
  • Strict controls apply to the production of wastes that may be toxic or may cause environmental damage. Safety regulations and practices must be maintained to avoid the risk of accidental release of harmful materials.
  • Mine reclamation activities are undertaken gradually. They include levelling the heaps of earth material, replacing the top soil with a fertile one, and planting trees in the mined-out areas.

Care must be taken to relocate streams, wildlife and other valuable resources.

Quarries and opencast workings can be reclaimed by filling the holes with solid wastes.

Eroded bare soil can be conserved by planting trees and grasses as a soil cover. This counteracts the impacts of wind, running water, rain and animals on the soil.

Reclaimed land can have many uses, such as agriculture, forestry, wildlife, habitation and recreation.

  • Dust levels can be controlled by spraying water on roads, stockpiles and conveyors. Other steps include filling drills with dust collection systems, and buying additional land around the mine to act as a buffer zone. Trees planted in these buffer zones can also reduce the visual impact of dust from the mining operations on local communities.
  • Noise can be controlled by careful selection of equipment, by insulation, and by enclosures around machinery.
  • The poisonous and toxic substances used in metal extraction must be treated properly before being directed into rivers and streams. Alternatively, these materials may be drained into reservoirs. There they can gradually percolate deep into the soil and evaporate into the air without causing much harm to the surrounding ecosystems.

In some mines, absorbent carpets are spread on the surface of the ground. They trap the toxic substances in the liquid chemicals used for mining. This prevents these chemicals from finding their way into water bodies.

Jaribu quiz ya ChemistryMaswali 30