Chemistry · Kidato 3

Topic 2; hardness of water

Dakika 13 za kusoma ·

Yaliyomo

The Concept Of Hardness Of Water

As water flows over the land, it dissolves many mineral substances. The dissolved minerals are deposited together with water in rivers, lakes and oceans.

Water is said to be hard if it contains some specific types of dissolved minerals. Not all dissolved salts make water hard.

Water is treated in water purification plants before it is piped to your home. The treatment removes only the insoluble particles and kills bacteria. So the water is still not pure.

The water contains natural compounds dissolved from rocks and soil. It may also contain traces of chemicals dumped from homes, farms and factories.

Water from an area where the rocks contain chalk, limestone, dolomite or gypsum contains dissolved calcium and magnesium sulphates and hydrogen carbonates. These salts make the water hard.

Hard water and soap

You can tell hard water from soft water when washing with soap. Hard water does not form lather easily. Instead, it forms a precipitate or scum.

Hard water needs much soap to react with all the dissolved minerals before enough lather forms. Therefore, hard water wastes soap during washing.

When soap is used with hard water, a "scum" forms on the surface. It is the result of a precipitation reaction between calcium and/or magnesium ions and soap.

Soaps are the sodium or potassium salts of long-chain organic acids. Soaps are made from animal fats by treatment with an alkali (NaOH or KOH).

Ordinary washing soap is a compound of stearic acid, C17H35COOH. The soap is the salt sodium stearate, C17H35COONa. Sodium stearate is soluble in water, but calcium stearate is not.

When soap is mixed with hard water, the calcium or magnesium salts in the water react with the soap and form a precipitate called scum. The scum is either calcium stearate or magnesium stearate.

Soap will not form any lather with water until all the calcium and magnesium ions have been precipitated. So hard water wastes soap. More soap may be needed for efficient washing.

The amount of soap needed to just produce froth can be used to estimate the hardness of water.

Soapy and soapless detergents

The problem of scum formation occurs only with soaps. Soapless detergents do not produce scum.

Trade names of some soapy detergents sold in Tanzania include Komoa, Kuku, Taifa, Mbuni, Mshindi, Changu, Jamaa and several other bar soaps.

Trade names of some soapless detergents include Omo, Foma, Tesa, Toss, Dynamo, Swan, etc.

Causes Of Permanent And Temporary Hardness In Water

Water is generally said to be hard if it contains soluble salts of calcium and magnesium. These salts are calcium and magnesium sulphates and hydrogen carbonates.

Hardness of water is caused by higher than usual levels of calcium (Ca2+) and magnesium (Mg2+) ions in the water.

How the ions get into water

As rain water passes through the atmosphere, it dissolves carbon dioxide to form a weak carbonic acid.

This solution passes over and through rocks containing chalk, limestone or dolomite. The rain water very slowly dissolves them:

H2CO3(aq) + CaCO3(s) → Ca(HCO3)2(aq)

The calcium hydrogen carbonate formed is soluble in water. It is responsible for the presence of calcium (Ca2+) ions in water.

Some rocks may contain gypsum (CaSO4.2H2O), anhydrite (CaSO4), kieserite (MgSO4.H2O) or dolomite (CaCO3.MgCO3). These dissolve to a limited extent in water.

The presence of these dissolved substances also makes the water hard. They dissolve sparingly in water to form Ca2+ and Mg2+ ions, which are responsible for water hardness.

Activity 1: Investigation Of The Causes Of Water Hardness

Materials

  • Test tube rack
  • Five clean test tubes
  • Measuring cylinder (100 cm3)
  • Calcium sulphate solution (1 mol dm-3)
  • Soap solution
  • Magnesium sulphate solution (1 mol dm-3)
  • Sodium sulphate solution (1 mol dm-3)
  • Potassium sulphate solution (1 mol dm-3)
  • Distilled water

Procedure

  1. Label five clean and dry test tubes as A, B, C, D and E.
  2. Add 10 cm3 of 1.0 M calcium, magnesium, sodium and potassium sulphate solutions and distilled water to the test tubes respectively.
  3. Add 5 cm3 of soap solution to each test tube.
  4. Shake the test tubes well and place them in the test tube rack.
  5. Observe the amount of lather formed in each test tube, and whether any precipitate (scum) is formed.

Results

Results of the experiment showing which minerals cause water hardness

  • Test tube A: salt present is calcium sulphate. Ions in solution: Ca2+, SO42-. Scum is formed. The water is hard.
  • Test tube B: salt present is magnesium sulphate. Ions in solution: Mg2+, SO42-. Scum is formed. The water is hard.
  • Test tube C: salt present is sodium sulphate. Ions in solution: Na+, SO42-. Lather is formed. The water is soft.
  • Test tube D: salt present is potassium sulphate. Ions in solution: K+, SO42-. Lather is formed. The water is soft.
  • Test tube E: distilled water. No ions. Lather is formed. The water is soft.

Interpretation of the results

From the experiment, we conclude that scum is produced when either a calcium or a magnesium salt is present in water. So high levels of calcium or magnesium ions in water are responsible for water hardness.

When the concentration of either of these minerals is over 150 milligrams per cubic decimetre (150 mg/dm3), water is considered to be hard. The upper limit allowed is 300 mg/dm3.

Types Of Hardness Of Water

The hard water in some areas can be softened simply by boiling the water. This is not true in all cases.

So hardness of water is divided into two types: temporary hardness and permanent hardness.

Temporary hardness

Temporary hardness is caused by dissolved calcium or magnesium hydrogen carbonates.

The most important characteristic of temporarily hard water is that it can be softened by simply boiling.

When the water is boiled, the soluble sodium hydrogen carbonate is decomposed to form the insoluble calcium carbonate.

Furring Of Kettles And Pipes

The decomposition of hydrogen carbonate causes the "furring" of kettles, hot water pipes and shower heads.

This means the inside of kettles, pipes and shower heads becomes coated with a layer of calcium carbonate (limescale). The layer forms because the hydrogen carbonate decomposes, according to the equation above.

Removing limescale

In many supermarkets, you can buy a limescale remover. It is often a solution of methanoic acid (formic acid).

This weak acid is strong enough to react with limescale, but not with the metal.

The insoluble limescale (carbonate) is dissolved to form a soluble compound, calcium methanoate. This compound can be flushed away with water.

2HCOOH(aq) + CaCO3(s) (insoluble) → Ca(HCOO)2(aq) (calcium methanoate, soluble) + H2O(l) + CO2(g)

Permanent Hardness

Permanent hardness in water is caused by soluble sulphates and chlorides of calcium and magnesium. These are CaSO4, MgSO4, CaCl2 and MgCl2.

This type of hardness cannot be removed by boiling the water. This is because boiling does not decompose the chlorides of calcium or magnesium.

Such water can only be softened by chemical treatment or by ion exchange methods.

The Difference Between Soft And Hard Water

Task: Differentiate soft from hard water.

Activity 2: Distinction Between Temporarily And Permanently Hard Water

Materials

  • Calcium carbonate
  • Dilute hydrochloric acid
  • 4 test tubes
  • Test tube rack
  • 1 litre of distilled water
  • Calcium chloride
  • Soap solution
  • Beaker
  • Heat source

Method

  1. Prepare carbon dioxide gas in the laboratory. Mix calcium carbonate with hydrochloric acid in a gas generator.
  2. Bubble the gas through a suspension of calcium carbonate in water. Shake well as you bubble, until most of the calcium carbonate has dissolved. Filter, and divide the filtrate into two test tubes, M and N.
  3. Prepare a 0.5M solution of calcium chloride. Divide it into two test tubes, P and Q.
  4. Prepare soap solution in a large beaker.
  5. Arrange the four test tubes in a rack.
  6. Heat the solutions in test tubes M and P to boiling. Allow them to cool.
  7. Add 10 cm3 of the soap solution to each of the four test tubes M, N, P and Q. Shake well and allow to rest. Observe lathering and scum formation.

Note

When calcium carbonate reacts with dilute hydrochloric acid, carbon dioxide gas is produced.

CaCO3(s) + 2HCl(aq) → CaCl2(aq) + H2O(l) + CO2(g)

When carbon dioxide gas is bubbled through a suspension of calcium carbonate in water for a long time, the insoluble calcium carbonate dissolves. It gives the soluble bicarbonate, and its presence makes the water hard.

CO2(g) + CaCO3(s) + H2O(l) → Ca(HCO3)2(aq)

The purpose of heating the solutions in test tubes M and P was to try to remove the water hardness.

Only the hardness in test tube M was removed by boiling, because it contains temporarily hard water.

The hardness in test tube P could not be removed by just boiling, because it contained permanently hard water. Calcium chloride cannot be decomposed by heat. So no change is expected after heating.

Results

  • Scum was formed in test tubes N, P and Q. P and Q contained more scum than N.
  • Lather was formed in test tube M only.
  • Test tube M contained temporarily hard water and test tube P contained permanently hard water. The hardness in M was removed by boiling, while that in P was not.
  • Test tubes P and Q contained permanently hard water. The hardness in this water could not be removed by mere boiling.

Treatment And Purification Of Hard Water

Process of hard water treatment and purification

Hard water causes problems. So it is often softened for use in factories, industries and homes.

Softening means removing the dissolved calcium and magnesium ions.

The methods of treating and purifying hard water are described below.

Boiling

Boiling removes temporary hardness in water, as you saw earlier.

Boiling causes calcium carbonate to precipitate. The hydrogen carbonates in the water are decomposed to carbonates, which are insoluble in water.

In this way, the calcium is removed. The calcium carbonate is insoluble, so it takes no further part in the reaction. An insoluble calcium salt cannot cause hardness.

However, this method uses a lot of fuel. This makes it expensive to do on a large scale.

Distillation

Distillation removes all impurities from water. This gets rid of both temporary and permanent hardness.

In distillation, the water is boiled. The steam is collected, cooled and condensed.

Distilled water is pure and is the softest water. All the dissolved substances have been removed.

Like boiling, it is an expensive option in terms of fuel used. But it is essential for some purposes, for example laboratory experiments and making drugs.

Addition of calcium hydroxide

Adding calculated amounts of calcium hydroxide can remove temporary hardness.

The quantity added must be properly calculated, because too much would cause hardness on its own account.

The amount of calcium hydroxide to add is calculated from the hardness of the water and the capacity of the reservoir (Clark's method).

The calcium hydroxide reacts with the hydrogen carbonates dissolved in the water. They precipitate as insoluble calcium carbonate.

Ca(OH)2(s) (slightly soluble) + Ca(HCO3)2(aq) → 2CaCO3(s) (insoluble) + 2H2O(l)

Addition of sodium carbonate (washing soda)

Washing soda removes both temporary and permanent hardness by precipitating calcium carbonate.

It reacts with calcium hydrogen carbonate (which causes temporary hardness) to form sodium hydrogen carbonate:

Na2CO3(aq) + Ca(HCO3)2(aq) → 2NaHCO3(aq) + CaCO3(s)

It also reacts with calcium sulphate (which causes permanent hardness) to form sodium sulphate:

Na2CO3(aq) + CaSO4(aq) → CaCO3(s) + Na2SO4(aq)

These sodium salts are soluble, but they do not make the water hard.

The calcium and magnesium ions are precipitated as insoluble calcium and magnesium carbonates. In ionic form, the reactions are:

Ca2+(aq) + CO3 2-(aq) → CaCO3(s)

Mg2+(aq) + CO3 2-(aq) → MgCO3(s)

Ion exchange

Another method that removes both temporary and permanent hardness is the use of ion exchange resin.

A typical ion exchanger is a container full of small beads. The beads are made of a special plastic called ion exchange resin.

The resin beads are porous and contain sodium ions.

When hard water flows through the resin, the calcium and magnesium ions in the water are exchanged for the sodium ions. The calcium and magnesium ions attach themselves to the resin.

This process removes calcium and magnesium ions from the water. They are replaced by sodium ions, which do not make the water hard.

Ion Exchange Column And Softeners

How an ion exchange column works

An ion exchange column removes Ca2+ and Mg2+ ions from the water. It replaces them with Na+ ions.

When all the sodium ions have been removed from the resin, the resin is regenerated. To do this, a concentrated solution of sodium chloride is poured through it.

The sodium ions remove the calcium and/or magnesium ions off the resin. The ion exchanger is then ready for use again.

Other ions could also be used instead of sodium for the resin. But sodium chloride is normally used to supply the sodium ions because salt is cheap.

Use of softeners

Many modern washing powders now have softeners added to them. The softeners are often phosphates.

The phosphate ions react with calcium ions to form calcium phosphate. This removes the hardness.

3Ca2+(aq) + 2PO4 3-(aq) → Ca3(PO4)2(s)

The Importance Of Hard Water Treatment And Purification

Task: describe the importance of hard water treatment and purification.

The importance of water in daily life is well known to everyone. Water from natural sources is never pure. It contains dissolved minerals. These minerals make the water unfit for direct uses.

Water from some sources contains dissolved calcium and magnesium compounds. These compounds are responsible for water hardness.

To make the water fit for various uses, it is imperative to remove the hardness. The following points state why it is important to treat and purify hard water:

  • Hard water wastes soap. To get enough lather with hard water, more soap is needed than with soft water. So it is important to soften the water. This saves soap and reduces the cost of washing. Laundry uses less soap and can be done at lower temperatures.
  • Treating and purifying hard water removes the possibility of limescale deposits forming in water boilers, kettles, washing machines, water heaters, shower heads and dish washers. Scale formed around the heating elements can cause the element to overheat and fail.
  • Treated and purified water leaves no scum on clothes during washing. Scum spoils the finishing of some fabrics. It forms nasty deposits (marks) on washed clothing.
  • Softened water does not block the water pipes. In industry, deposits of scale can block the pipes in boilers. This is a safety hazard. Pressure could build up until there is an explosion. A similar coating can form in hot water pipes at home and in central heating systems.

The Importance Of Hard Water In Daily Life

Task: state the importance of hard water in daily life.

Hard water is not always a disadvantage. The following points explain its importance

  • The dissolved calcium and magnesium salts improve the taste of water. Distilled water is tasteless and quite unpleasant to drink. This is why water-processing plants add some salts to distilled water to make it tasty.
  • Calcium dissolved in hard water is an essential mineral for the growth of bones and teeth. It makes our teeth and bones hard, strong and resistant to shear and pressure.
  • In some places, old lead pipes are used for water supply. Lead is very poisonous, and a little of it can dissolve in soft water. But the carbonate (CO3 2-) or sulphate (SO4 2-) ions present in hard water react with lead. They form a coating of lead carbonate or lead sulphate. This coating prevents lead from dissolving. This prevents lead poisoning.
  • A coating of calcium carbonate inside pipes, boilers and radiators helps to prevent corrosion.
  • In recent years, it has been suggested that drinking hard water helps to prevent heart diseases.
  • It has also been found that hard water is good for brewing beer.
Jaribu quiz ya ChemistryMaswali 30