Laboratory techniques and safety
Dakika 38 za kusoma ·
Yaliyomo
Laboratory Techniques And Safety
What Is A Laboratory?
A laboratory is a room or building specially designed for conducting various scientific experiments.
Features Of An Appropriate School Laboratory
An appropriate school laboratory has the following features
- A room with enough space for carrying out scientific experiments.
- A store for keeping laboratory apparatus, chemicals and reagents.
- An office where the laboratory technician can sit and design scientific experiments.
- Enough ventilation to let in fresh air and light.
- Wide doors and several exits for emergency evacuation in case of an accident.
- A wide table in front of the laboratory room, fitted with sinks. The teacher or technician uses it for experiment demonstrations.
Rules And Safety Precautions In A Chemistry Laboratory
Laboratory Rules
Chemistry is best studied through doing experiments. Most experiments are conducted in the laboratory.
It is important to read and follow laboratory rules to avoid causing accidents. Your teacher will teach you more rules.
The following are some important laboratory rules
Entering and Dress
- Do not enter the laboratory without permission from your teacher or laboratory technician.
- Wear safety goggles all the time while in the laboratory. Obey this rule whether you are working on an experiment or simply writing in your laboratory notebook.
- Contact lenses are not allowed. Even when worn under safety goggles, various fumes may collect under the lens and cause serious injuries or blindness.
- Put on closed shoes and trousers when in the laboratory. Sandals and shorts are strictly prohibited.
- Tie back long hair when using open flames.
Behaviour
- Never walk or run unnecessarily in the laboratory.
- Eating, drinking and smoking are strictly prohibited in the laboratory.
- Never eat or drink from laboratory glassware.
- Do not perform any experiment not authorized by your teacher or laboratory technician. If you are curious about trying a procedure not covered in the experimental procedure, consult your teacher or laboratory technician.
- Use equipment or apparatus only for its designated use.
- Never take away anything from the laboratory without your teacher's permission.
- Notify your teacher or technician immediately in case of an accident.
- Always wash your hands after experiments.
Handling Chemicals
- Never taste anything.
- Never directly smell the source of any vapour or gas. Instead, drift a small sample to your nose. Do not inhale the vapour directly. Take in only enough to detect an odour, if one exists.
- Never use your hands to transfer chemicals. Use a spatula instead.
- Know what chemicals you are using. Carefully read the label twice before taking anything from the reagent bottle. Do not interchange labels.
- Use only those chemicals needed in the activity. Keep all lids closed when a chemical is not in use.
- Excess reagents are never to be returned to stock bottles. If you take too much, dispose of the excess.
- Do not use the same spatula to remove chemicals from two different containers. Each container should have a different spatula.
- Replace all stoppers, covers and caps as soon as you finish using them. Be careful not to exchange stoppers from two different containers.
- Many common reagents, for example alcohol, acetone and carbon disulphide, are highly flammable. Do not use them anywhere near open flames.
- Pour more concentrated solutions into less concentrated solutions to avoid violent reactions. For example, always add acid to water, not water to acid. If you pour water into acid instead, the heat of reaction will cause the water to explode into steam, sometimes violently, and the acid will splash.
- If chemicals accidentally splash onto your skin or eyes, flush immediately with plentiful amounts of water. Then report to your teacher or lab technician.
Heating and Flames
- Never point a test tube or vessel that you are heating at yourself or your colleague.
- Never heat a liquid in a closed container. The expanding gases produced may blow the container apart, injuring you or others.
- Beware of hot glass, because it looks exactly the same as cold glass. Never touch it with your hand.
- When heating glassware, use wire gauze or a ceramic screen. This will protect the glassware from the flame of a Bunsen burner.
- Always adjust the Bunsen burner to give a luminous flame when not using it (or simply turn it off).
- Use a lighter or wooden splint to light burners. Do not use papers. Always strike the match before turning on the gas supply.
- Make sure all the burners are turned off before leaving the laboratory. Check that the gas tap is off as well.
Gases and Ventilation
- Keep all windows open for proper ventilation.
- When carrying out an experiment where you expect harmful gases to be produced, use the fume chamber. The fume chamber helps to disperse hazardous gases and vapours safely.
- In case of a gas leakage, turn off the gas tap and open the windows. Leave the room immediately.
Glassware and Cleaning Up
- Never use broken or chipped glassware. If glassware breaks, inform your teacher and dispose of the glassware in the litter bin.
- Dispose of chemicals properly. Unless you are told otherwise, assume that only water may be poured in the laboratory sinks.
- When an experiment is completed, always clean up your work area and dispose of broken glass properly. Return all equipment to its proper storage places.
Electricity, Gas and Water
- Do not touch any electrical equipment with wet hands.
- Turn off any gas or water taps that are not in use.
The Safety Measures For A Chemistry Laboratory
The chemistry laboratory can be a place of discovery and learning. However, laboratory work by its very nature can be dangerous if proper common-sense precautions are not taken.
Effort has been made to remove explosives, highly toxic substances and carcinogenic substances from the experiments you will perform. However, some hazard cannot be avoided because a variety of chemicals and glassware are used.
You are expected to learn and follow all safety guidelines. This keeps the laboratory safe for you, the people you work with and those near you.
Important laboratory safety measures to obey
- Label and lock all storage areas, cupboards, drawers, storage cabinets, refrigerators and similar places. Locking prevents accidental contact with chemicals and interference with equipment.
- Know the location, use and limitations of the safety devices. These include fire extinguishers, fire blankets, the fume hood, spill cleanup materials, the first aid kit, eyewash stations and the fire alarm.
- Keep all chemicals in properly labelled containers. This prevents the accidental use of the wrong chemical in an experiment.
- Know the right safety measures to take when exposed to different hazardous materials. Your teacher or laboratory technician can give you this information.
- Store separately all chemicals that react with each other.
- Be aware of how laboratory furniture and equipment interact with the chemicals used or stored in the laboratory. For example, oxidizers should not be stored directly on wooden shelves.
- Use fume hoods, cupboards or chambers whenever possible.
- Never store food in a refrigerator or freezer where hazardous chemicals are stored. Also, do not eat anything you find in the laboratory, or in the laboratory freezer or refrigerator.
- Make sure fire extinguishers are in good condition. Report any broken seals, damage, low gauge pressure or improper mounting to the teacher or laboratory technician. If the seal is broken, assume the fire extinguisher has been used and must be recharged. (Note: Do not use a fire extinguisher unless you are trained and feel confident to do so.)
- Inspect stored chemicals regularly to make sure they have not expired. Note the date when bottles were received and the date when they were first opened. Note the expiry dates of chemicals and their special storage conditions.
- Remove safety hazards by keeping laboratory work areas in good order.
- The laboratory must have wide emergency exits and wide windows. Wide exits make evacuation easy in an emergency. Wide windows let enough air enter and circulate in the laboratory. (Note: Keep at least two clear passages to the laboratory exits.)
- Always keep tables, seats, fume hoods, floors and desks clear of unnecessary material.
- Inspect all equipment before use. Also check it regularly to make sure it is safe to use.
- If an experiment must be left unattended, place a note next to the apparatus. The note should show the chemicals involved, your name and the telephone number where you can be reached in an emergency.
- Keep the laboratory floor clean and dry at all times. Clean up spills of water or chemicals immediately. Then tell other laboratory workers about the possible slipping hazard.
- The laboratory must be equipped with portable fire extinguishers and other safety devices. Clear instructions on how to use them in an emergency must be provided.
- Inspect containers used for holding or storing chemicals for leaks or other damage. They should have tight stoppers or covers.
- All experimenters and other people working in the laboratory should wear protective gear to reduce exposure to hazards. This gear may include lab coats, hand gloves, gumboots, safety goggles and aprons.
- There should be a manual or instruction guide on how to treat spills of different chemical substances.
- Label the fume chamber. Keep it in good condition to reduce unexpected gas leaks or emissions.
- Label gas cylinders, store them properly and support them. They should also be in good working condition all the time.
- Equip each laboratory with enough first aid kits.
- Install equipment for monitoring contamination. It gives alerts of any possible danger.
Note:
All the rules and safety measures above apply to all research, teaching and academic laboratories. However, your laboratory may need some more rules for specific materials and equipment.
First Aid
First aid is the help given to someone who is injured or sick before the victim gets further medical assistance. Any person can give this help, even without knowledge of a medical profession.
Whenever an accident happens, something must be done immediately to help and save the life of the victim. Always be ready to give a hand when an accident happens close to you. To give aid effectively and successfully, you must have elementary knowledge of how to help different victims.
If you do not know how to help a certain victim, ask someone else to help. Do not try to help if you do not know where to start. You may make the victim's condition worse without knowing it. However, this must not be an excuse for failing to help. Always be ready to give some kind of help.
First aid helps to
- relieve pain and bring hope to the victim.
- prevent permanent disability.
- prevent the victim's condition from getting worse.
- reduce the possibility of death.
- shorten recovery time.
Possible Causes Of Accidents In A Chemistry Laboratory
Accidents may happen in a school laboratory if the greatest care is not taken.
Accidents in the laboratory are mainly cuts on parts of the body such as the hands, fingers, legs or head. Others are:
- burns from flames
- scalds from boiling fluids
- bruises and grazes from accidentally falling on a slippery floor
Causes Of Accidents In The Laboratory
Some possible causes of accidents in the laboratory include
- Failure to follow the correct experimental procedures. For example, pouring water into an acid instead of pouring an acid into water, as the rule is.
- Neglecting some laboratory rules. Examples are ignoring to wear protective gear, tasting the chemicals, and eating or drinking while in the laboratory.
- Failure to adhere to proper conduct in the laboratory. Examples are running unnecessarily and conducting experiments without your teacher's or technician's permission and guidance.
- Improper use or handling of laboratory equipment and apparatus when conducting experiments. This could lead to breakage, which in turn causes cuts, bruises, grazes, etc.
- A slippery laboratory floor. It can cause fractures, cuts, bruises, grazes, etc.
- Accidental spillage of chemicals on body parts such as the hands, face, eyes, etc. This could lead to burns and damage.
- Poor ventilation in the laboratory. It may cause suffocation (due to inadequate oxygen supply) and poisoning (by inhaling poisonous gases produced when experimenting).
- Improper disposal of chemical wastes. It may result in explosions, burns or even fires.
- The leaking of gases from taps or cylinders. It may cause fires or even explosions.
- Use of wrong reagents. This happens due to incorrect labeling of chemicals, or use of reagents or chemicals that have expired. It may cause burns, poisoning or damage to apparatus or equipment.
- Inadequate prior information or knowledge on procedures and hazards associated with certain practical activities or reactants. It may result in burns, poisoning or explosions.
- Loose or improperly plugged electrical appliances. They may cause electric shock, especially when touched with wet hands and during fixing of sockets.
In general, most laboratory accidents are a result of negligence and carelessness of experimenters.
They are also due to failure to follow the laboratory rules and general safety measures.
First Aid And First Aid Kit
The Items Found in a First Aid Kit
A First Aid Kit is a collection of supplies and equipment that is used to give medical treatment.
In the laboratory, the box is usually kept in a place where it can be easily reached in case of an accident. It is preferably kept on the wall.
Each student must be familiar with the tools and chemicals kept in the kit. Each student must also learn how to use them to provide first aid to a victim.
How Each First Aid Kit Item is Used
The list below shows the types of tools, chemicals and items found in a First Aid Kit and their functions.
- First aid manual: contains guidelines on how to use the items in the first aid kit.
- Sterile gloves: worn on hands when attending bleeding cuts or wounds. They avoid infecting wounds and prevent direct contact with the victim's body fluids.
- Sterile dressing: stops bleeding.
- Antiseptic agent: cleaning and disinfection of wounds, cuts, bruises, grazes or blisters.
- Soap: washing hands, wounds and equipment.
- Antibiotic ointment: prevents infection on cuts and bruises in or near the eye.
- Burn ointment: applied on burns to prevent infection.
- Petroleum jelly: soothing broken skin.
- Plaster or adhesive bandage: covering small wounds or cuts.
- Sterile gauze: covering wounds to protect them from dirt or germs.
- Eye wash solution: flushing the eyes, or used as a general decontaminant.
- Thermometer: recording body temperature.
- Antibiotic towelettes or cotton wool: cleaning and drying cuts and wounds.
- Iodine tincture: dressing fresh cuts and bruises.
- Pain relieving drugs such as aspirin, paracetamol, panadol, etc: relieving mild pains.
- Liniment: reducing muscle pain.
- Mild antibiotics: treating mild bacterial infections on the skin, ear, nose and mouth.
- Gentian violet solution: applied on minor wounds and treatment of serious heat wounds.
- Hydrogen peroxide solution: cleaning wounds.
- Methylated spirit (70% alcohol): cleaning cuts and bruises.
- Bandages: dressing wounds and cuts, and immobilizing injured limbs.
- Scissors or razor blade: cutting dressing materials.
- Dental kit: treatment of broken teeth, loss of crown or filling.
- Safety pins (small and big): splinter removal and securing triangular bandage slings.
- Tweezers: splinter or stinger removal.
- Resealable oven bag: container for contaminated articles.
- Moleskin: applied to blisters or hot spots.
- Triangular bandage: used as a sling, towel or tourniquet.
- Boiled, clean water: washing hands and drinking.
- Nasal spray decongestant: for nasal congestion from colds or allergies.
- Torch: source of light.
- Whistle: blown to call for help.
First Aid Procedures
Sometimes accidents may occur in the laboratory for one reason or another. Whenever an accident occurs, one must be ready and prepared to assist.
The following are some of the health problems that may require first aid. The procedure to follow when providing help is also given.
Bleeding
Bleeding is the loss of blood from the body. It usually occurs from a visible wound.
Bleeding may be external or internal. It may come from an artery, a vein or a capillary. Bleeding may be severe or light.
Excessive loss of blood may cause death.
(a) Internal bleeding
Signs and symptoms of internal bleeding include the following
- Bruised, swollen, tender or rigid abdomen
- Bruises on the chest, neck or legs, or signs of fractured ribs
- Vomiting or coughing up blood
- Wounds that have penetrated the skull, chest or abdomen
- Bleeding from body cavities such as the ears, nose, rectum or vagina
- Abdominal pulse and difficulty breathing
- Cool, moist skin
- Fractures
Procedure
- First aid in the field for internal bleeding is limited. If the injury appears to be a simple bruise, apply cold packs. They slow down the bleeding, relieve pain and reduce swelling.
- If you suspect more severe internal bleeding, carefully monitor the patient. Be prepared to administer CPR if required (and you are trained to do so).
- Seek medical advice immediately if the situation seems to be getting worse.
Severe Bleeding
Procedure
- Severe bleeding, where blood oozes out rapidly, must be stopped at once. You can do this by applying direct pressure to the wound.
Use a dressing if one is available. If it is not available, use a rag, towel, piece of clothing or just your fingers.
If the wound is large, press the edges of the wound together, but do it firmly. Do this only if there is no fracture.
- Lay the victim down in a comfortable position.
- If the wound is on a limb, and the limb is not fractured, raise the wound above the level of the heart. Then continue to apply direct pressure.
Do this only if bleeding continues and if it does not cause pain.
- If the bleeding still cannot be controlled, apply pressure at a pressure point.
For wounds of the arms or hands, the pressure points are
- the inside of the wrist (radial artery, where a pulse is checked)
- the inside of the upper arm (brachial artery)
For wounds of the legs, the pressure point is at the crease in the groin (femoral artery).
- When the bleeding stops, clean the wound carefully and thoroughly with a suitable disinfectant.
Do not remove any objects stuck in the wound. Removing them would lead to more bleeding.
- Place sterile gauze on the wound and press it down firmly. Cover it with a soft material and hold it in position with a firm bandage.
After the bandage is in place, check the pulse to make sure blood circulation is not interrupted.
A slow pulse rate, or bluish fingertips or toes, signal that the bandage may be hindering blood circulation.
- Seek medical help immediately.
Important
Once pressure is applied, keep it in place. If dressings become soaked with blood, apply new dressings over the old ones.
The less a bleeding wound is disturbed, the easier it will be to stop the bleeding.
Light Bleeding
Procedure
- Place the victim in a comfortable resting position.
- Elevate the injured part while applying pressure. Do this only if the wound is on a limb and you do not suspect a fracture.
- Gently and thoroughly clean the wound using water and antiseptic, or common salt solution.
- Cover the wound with sterile gauze or a clean dressing dipped in iodine solution.
- Dress and bandage the wound.
- Take the victim to hospital if the bleeding still continues.
Nose Bleeding
Bleeding usually occurs near the tip of the nose.
The bleeding may be a result of high blood pressure, rheumatic fever or injury.
Nose bleeding is also likely to occur at high altitude, because of low atmospheric pressure or extreme coldness.
Procedure
- Let the victim sit calmly. This makes the heartbeat slow down and so reduces bleeding.
- Loosen clothing around the neck and chest.
- Let the victim sit upright and lean the head forward slightly.
By remaining upright, the victim reduces the blood pressure in the veins of the nose. This discourages further bleeding.
Leaning forward helps the victim avoid swallowing blood, which can irritate the stomach.
- Have the victim pinch the nose with the thumb and index finger to keep the nostrils shut. Ask the victim to breathe through the mouth.
Let the victim continue pinching for a few minutes.
- Apply a cold, wet compression over the nose, face and the back of the victim's neck.
- When the bleeding stops, gently clean the nostrils.
- If the bleeding does not stop after 20 minutes, take the victim to hospital immediately.
To prevent re-bleeding after the bleeding has stopped
- Ask the victim not to pick or blow the nose, and not to bend down, until several hours after the bleeding.
- Let the victim keep the head higher than the level of the heart.
If re-bleeding occurs
- Ask the victim to blow out forcefully to clear the nose of blood clots.
- Spray both sides of the nose with decongestant nasal spray.
- Pinch the nose as described above and seek medical help.
Suffocation
Suffocation is a condition in which the lungs are not getting enough oxygen, causing difficulty in breathing. Foam can also appear in the mouth and nostrils.
If suffocation is complete (no air at all reaches the lungs), the lack of oxygen and the excess carbon dioxide in the blood cause immediate loss of consciousness.
The heart continues to beat briefly. However, death follows in a matter of minutes unless emergency measures are taken to get breathing started.
Suffocation can be caused by
- drowning
- electric shock
- gas or smoke poisoning
- choking
- asthma
- severe infections of the throat
- other causes
Procedure
- Remove the cause of suffocation, or remove the victim from the cause. Loosen tight clothing around the neck.
- Make sure the victim's airway is open so that air can reach the lungs.
To do this, lay the victim on his or her back. Put one hand on the victim's forehead and the other on the chin. Tilt the head backwards to open the airway.
Tilt the head until the chin points straight upwards. If the airway is blocked by fluid or a solid, remove it.
- Administer cardiopulmonary resuscitation (CPR). This involves blowing air into the victim's mouth (mouth-to-mouth breathing).
To do this, pinch the nose and close up the mouth. Take a deep breath and then blow hard into the victim's mouth.
Watch the chest rise. Repeat the procedure until the victim's breathing is restored.
If the person does not respond, go for chest compressions.
- Do compressions by placing the palm of one hand in the space between the nipples, and the other hand over it. Push the chest using your upper body weight.
Take care to prevent chest injury or fracture.
Give two compressions every second, or one hundred per minute. After thirty compressions, go for mouth breathing again.
Repeat the procedure until natural breathing is restored.
- Keep the casualty warm using a light blanket.
- Take the casualty to hospital immediately.
Choking
Choking occurs when food or a foreign object blocks the upper part of the windpipe. This interferes with normal breathing.
The signs of this problem include difficulty in breathing and speaking.
Have you ever been with a person who is choking? Did you know what to do?
When attending a person who is choking, first notice whether the person can talk, breathe or cough.
Caution: Do not try to slap the person on the back. The slapping may only cause the food to become more deeply lodged in the airway.
Choking: Heimlich Manoeuvre
Procedure
- Ask the victim to cough up the object.
- If the object remains stuck, give firm but gentle taps between the shoulder plates.
- If the object is still stuck, apply quick abdominal thrusts. This is called the Heimlich manoeuvre. Do it as follows:
- Stand behind the victim and make him or her lean forward slightly.
- Put your arms around the person. Place your fist just below the breastbone. Grasp your fist with the other hand, near the top of the victim's stomach.
- Press your fist onto the victim's abdomen. Give a series of quick, sharp upward and inward thrusts to dislodge the object.
Poisoning
A poison is any substance that can harm the body or seriously endanger health when taken into the body.
A poison may get into the body through inhaling, swallowing, wounds or skin cuts. It may also be absorbed into the body in other ways.
Potential poisons include poisonous fumes (or gases), laboratory chemicals, and even medical drugs and medicines.
In every household, there are different kinds of things that are poisonous. Some are deadly even in a very small dose. Others may be more or less harmless when taken in small quantities.
Examples of poisonous substances at home
- kerosene
- disinfectants
- paints
- medicines
- artificial fertilizers
- and others
Some signs and symptoms of poisoning
- nausea
- vomiting
- abdominal cramps
- pain
- difficulty breathing
- diarrhea
- abnormal skin colour
Other signs and symptoms
- breath that smells like the chemicals
- chemical burns
- empty medication bottles or scattered pills
- sleepiness
- confusion
- other unexpected signs
Procedure for helping a poisoned person
- Call for medical help immediately if the person shows one or more of these signs:
- drowsy or unconscious
- having difficulty breathing, or has stopped breathing
- uncontrollably restless or agitated
- For the time being, find out what caused the poisoning. Look for the poison and identify it.
- If the person has been exposed to poisonous fumes such as carbon monoxide, get him or her to where there is fresh air immediately.
If the poison is in the eye
- Wash the eye with a lot of clean water.
- Ask the victim to blink as much as possible.
- Do not rub the eye.
If the person swallowed the poison
- Remove anything remaining in the mouth.
- Induce vomiting if the poison is not a strong acid or alkali, because these are corrosive substances. Non-corrosive substances include medicines and soaps.
- Vomiting can be induced by inserting your finger in the victim's throat until the finger touches the epiglottis.
- Do not induce vomiting if the poison swallowed is corrosive. Corrosive substances include kerosene, bleach, detergent, laboratory acid, disinfectant or certain toiletries.
- If the suspected poison is a household cleaner or other chemical, read the label. Follow the instructions for handling accidental poisoning.
- Neutralize the poison by giving the victim plenty of milk to drink, an egg white or water.
If the poison is on the skin
- Remove any clothing from the affected part.
- Wash the affected area thoroughly with a lot of water.
- Do not apply any ointment.
Finally, make sure the person is breathing. If not, start rescue breathing and CPR.
Note: Take the poison container, or any pills, pill bottle or pill blister pack, with you to the hospital.
Shock
Shock is a condition in which the body system fails to take enough blood to the vital organs.
If untreated, it can lead to permanent organ damage or death.
The vital organs include the heart, the lungs, the brain, the kidneys and the liver.
Causes
Shock may result from
- bad news
- heatstroke
- severe illness
- blood loss
- dehydration
- poisoning
- severe burns
- an accident
- other causes
Shock: Signs And Symptoms
A person experiencing shock shows various signs and symptoms. They include the following
- The skin becomes cool and moist. The skin, lips and fingernails may look pale or grey.
- The pulse rate is weak and rapid. Breathing may be slow and shallow.
- The limbs may tremble and get weak.
- The eyes lack lustre and may seem to stare. Sometimes the pupils are dilated.
- As the shock develops, the victim may feel nausea and even vomit. Eventually he or she may become restless, nervous, aggressive and finally conscious or unconscious. If conscious, the person may feel faint, very weak or confused.
Shock: Procedure
- Control any cause of shock, such as bleeding.
- Lay the person down with his or her feet higher than his or her head. This is the shock position.
- Loosen tight clothing, laces, belts and shoes.
- Turn the person on his or her side. This prevents choking if the person vomits or bleeds from the mouth.
- Keep the person warm and comfortable if he or she feels cold. Cover the victim with a blanket or any heavy clothing.
- Seek treatment for injuries such as bleeding or broken bones.
- Give CPR if the person does not appear to breathe well, cough or even move.
- Seek medical help immediately.
Electric Shock
An electric shock occurs when a person comes into direct contact with electricity.
Exposure to electricity may result in injury or even death. The injuries may be burns, or physical injuries from being thrown by the electric current.
Procedure
- Switch off the main switch immediately if possible.
- If you cannot switch it off, separate the casualty from the source of electricity. Use a non-conducting object such as a dry wooden stick, cardboard, plastic or rope.
- Loosen any tight clothing, necklaces, bangles and similar items.
- If the person is unconscious, apply mouth-to-mouth respiration (CPR) immediately.
- Treat for shock, burns, bruises or other injuries the victim may have. Lay the victim down. If possible, put the head slightly lower than the trunk, with the legs raised (shock position).
- Take the person to the hospital immediately.
Caution
- Do not touch the person with your bare hands if he or she is still in contact with the electric current.
- Do not go near high-voltage electricity until the power is turned off. Instead, call for help immediately.
- Do not move a person with an electrical injury unless the person is in immediate danger.
Bruises
A bruise is an injury beneath the skin. You can identify a bruise by pain, swelling or a mark under the skin.
A bruise forms when a blow (a hard hit) breaks the blood vessels near the skin's surface. A small amount of blood then leaks into the tissues under the skin. The trapped blood appears as a blue-black mark.
Procedure
- Wash the bruised part of the body.
- Apply a cold compress to the injury. This can be a cloth dipped in cold water, or ice wrapped in a cloth. It helps reduce pain and swelling, and speeds up recovery.
- If the bruise is on a limb such as an arm or leg and covers a large area, keep the limb raised as much as possible for the first 24 hours.
- After 48 hours, apply a cloth dipped in tepid water to the bruise for about 10 minutes, three times a day. This increases blood flow to the affected area and so speeds up healing.
Vomiting
Vomiting is an involuntary ejection of the contents of the stomach through the mouth.
Possible causes of vomiting
- Allergic reactions
- Diseases, e.g. malaria
- Physiological conditions, e.g. pregnancy
- Food poisoning
- Unpleasant smell or taste
- Drinking contaminated water
- Inhaling poisonous fumes
- Over-eating
Procedure
- Give the victim an oral rehydration drink or oral rehydration salt solution. You may also give a lot of any clear fluids.
- Allow the person to rest completely.
- Take the victim to hospital if any of the following happens:
- Vomiting continues persistently.
- The victim vomits blood.
- The victim has a high fever.
- The victim is very dehydrated. You will see this when the mouth and skin become very dry.
Fainting
Fainting is a sudden loss of consciousness. It is caused by a temporary fall in the supply of blood and oxygen to the brain.
Sometimes it is caused by emotional shock or prolonged standing. The person feels weak, sweats and then falls down.
Procedure
- Loosen or remove any tight clothing from the victim.
- Make the victim lie down on his or her back.
- Raise the legs of the victim above the level of his or her head (shock position). This increases the flow of blood to the brain.
- Make sure the victim gets plenty of fresh air.
- If there is no improvement in a few minutes, rush the victim to the hospital.
Caution: Do not try to warm the victim.
Muscle Cramps
A muscle cramp is a muscle that contracts involuntarily and forcibly and does not relax.
A muscle that contracts involuntarily is called a "spasm". If the spasm is forceful, it becomes a cramp. Therefore, muscle cramps occur because of uncontrolled muscle spasms.
Signs and symptoms
- A sharp, sudden and painful spasm, or tightening of a muscle (especially common in the legs).
- Muscle hardness
- Twitching of the muscle
- Persistent cramping pains in the lower abdominal muscles
Causes
- Imbalance in certain minerals, body fluids, hormones and chemicals that allow our muscles to stretch and contract.
- Malfunctioning of the nervous system.
- Excessive physical activity and hormonal imbalances cause us to sweat. This brings about the loss of many essential minerals, such as potassium and calcium, which our body muscles need.
Procedure
- Lay the victim down.
- Gently massage and stretch out the cramped muscle(s).
- Apply some anti-cramp ointment to the affected area.
- If the problem persists, seek medical help immediately.
(The source also has a figure titled "Stretching and massaging the muscles".)
Hiccups
Hiccups are caused by a sudden involuntary contraction of the diaphragm muscles. This gives a characteristic "hic" sound.
Many cures for hiccups exist. They are thought to work because they increase the level of carbon dioxide in the blood, which usually stops hiccups. (See procedures 1-3 below.)
Hiccups can also be relieved if the vagus nerve is stimulated. This nerve runs from the brain to the stomach.
Procedure
- Give the affected person a polythene bag. Encourage him or her to re-breathe his or her own expelled air.
- Ask the person to drink a glass of cold water quickly.
- Tell the victim to hold his or her breath for as long as possible.
- Ask the victim to pull on his or her tongue.
- The victim may swallow finely crushed ice.
- Children can be given a teaspoonful of a weak solution of sodium bicarbonate or lemon juice.
- Place one teaspoonful of dry sugar or honey on the back of the victim's tongue. You can repeat this 3 times at 2-minute intervals.
Basic Chemistry Laboratory Apparatus And Their Uses
Instruments used for carrying out different experiments in the laboratory are called laboratory apparatus.
Laboratory apparatus can be classified according to their uses as follows
- Apparatus for holding things, e.g. test-tube holder, retort stand and clamp, test-tube rack, tongs and tweezers.
- Apparatus for taking measurements, e.g. thermometer, burette, pipette, measuring cylinder, measuring flask, beam balance, electronic balance, common balance, measuring syringe, beaker and stop watch.
- Apparatus for heating substances, e.g. boiling tube, pipeclay triangle, crucible and lid, wire gauze, deflagrating (combustion) spoon, Bunsen burner, spirit lamp, tripod stand, evaporating dish, wire gauze and stove.
- Apparatus for doing chemical reactions (or testing), e.g. beaker, test tube, dropper, flask, watch glass, gas jar and thistle funnel.
- Apparatus for filtering, e.g. filter funnel, filter paper and cotton wool.
- Apparatus for grinding, e.g. mortar and pestle.
- Apparatus for storage, e.g. reagent bottles and wash bottle.
- Apparatus for scooping, e.g. spatula.
- Apparatus for safety, e.g. goggles and hand gloves.
Common Chemistry Laboratory Apparatus
The apparatus used in a chemistry laboratory
Task: List the apparatus used in a chemistry laboratory.
Chemistry laboratory apparatus according to their uses
Task: Categorize chemistry laboratory apparatus according to their uses.
The apparatus can also be classified based on the materials they are made of.
Most of the apparatus are made of glass. Others are made of metal, plastic or wood. Just a few are made of clay and asbestos.
The table below summarizes some common laboratory apparatus and their uses. Each item is written as: Apparatus – Material – Uses.
Composition And Uses Of Some Chemistry Laboratory Apparatus
- Test tube – Glass – Holding chemicals or heating substances.
- Funnel – Glass or plastic – Leading liquids into containers, and for filtration purposes.
- Beaker – Glass or plastic – Holding, heating and mixing liquids.
- Flask – Glass – Holding, heating and titrations.
- Retort stand – Metal (iron) – Holding apparatus during heating.
- Tripod stand – Metal (iron) – Holding apparatus during experiments.
- Gas jar – Glass – Gas collection.
- Wash bottle – Plastic – Washing.
- Crucible – Ceramic or non-reactive metal – Heating.
- Test tube holder – Metal and plastic or wood – Holding test tubes while heating.
- Weighing balance – Metal and plastic – Measuring weight (or mass).
- Spatula – Metal – Scooping small quantities of powder or crystalline chemicals.
- Condenser – Glass – Cooling hot liquids.
- Pipette – Glass – Accurate measurement of specific volumes of liquids for titrations.
- Burette – Glass – Titrations.
- Trough – Glass – Assists in gas collection.
- Tongs – Metal – Picking and holding hot substances and apparatus.
- Measuring jar – Glass – Measuring volumes of liquids.
- Thistle funnel – Glass – Leading liquids into containers and apparatus.
- Dropper – Glass and rubber – Dropping indicators into reagents.
- Mortar and pestle – Clay – Crushing or grinding substances.
- Wire gauze – Metal – Even distribution of heat during heating.
- Spring balance – Metal – Measuring weight.
- Distillation flask – Glass – Distillation.
- Combustion spoon – Metal – Burning powder in jars.
- Thermometer – Glass and liquid metal – Measuring temperature.
- Delivery tube – Glass – Allowing gases to pass through.
- Bunsen burner – Metal – Heating substances.
- Separating funnel – Glass – Separation of immiscible liquid mixtures.
- Measuring cylinder – Glass or plastic – Measuring volumes of liquids.
- Measuring syringe – Plastic – Sucking in and measuring specific volumes of liquids.
- Stopwatch – Plastic or glass and metal – Accurate measurement of time.
- Watch glass – Glass – Used as a surface to evaporate some liquids, to hold substances being weighed or observed, or as a cover for a beaker.
- Boiling tube – Glass – A large test tube. It is used to heat substances requiring strong heating, or when the sample is too large for a test tube.
- Evaporating dish – Ceramic – Heating and evaporating liquids and solutions.
- Filter paper – Paper – Filtration.
- Test tube rack – Wood or plastic – Placing test tubes.
- Reagent bottle – Glass – Storing different chemicals.
- Wash bottle – Plastic – Storing distilled water.
- Safety goggles – Glass – Protecting eyes from chemical spills, strong light and harmful vapours.
- Bell jar – Glass – Keeping gases, moisture, air, etc. or creating vacuums.
Activity 1
Your teacher will guide you on how to measure the volume of liquids using the other apparatus.
Aim: To measure the volume of liquids using different apparatus.
Procedure
- Pour some water into a graduated measuring cylinder with a capacity of 100 cm3. Add the water one drop at a time, up to the 25-cm3 mark.
- While adding water, position yourself at eye-level with the mark on the cylinder. This will enable you to obtain the most accurate measurement. To simplify reading the level of the water, you may use coloured water.
- Select a volumetric flask measuring 50 cm3. Pour the water into the flask until it reaches the mark on the flask's neck.
- Position yourself at eye-level with the mark. You will obtain the most accurate reading when the mark appears straight rather than elliptical. To obtain this, put the flask on a flat table.
- Add water one drop at a time. Do so until the bottom of the curved surface of the water exactly matches the mark on the flask.
Activity 1.2
Aim: To measure the masses of solid substances.
Materials: chemical, electronic or spring balance, watch glasses, and various substances such as sand, sugar, salt, flour, stones and fruits.
Procedure
- Put an empty watch glass on the weighing balance. Note down its mass. Record this as mass M1.
- Place the various items you have on the watch glass, one item at a time. Note down the mass. Record this as M2.
Note: To obtain the mass of an object, subtract the mass of the empty watch glass from the mass of the watch glass and the substance. That is, M2 – M1.
Warning Signs
Chemical warning signs are safety symbols found on containers, especially those used in the laboratory.
The symbols are also found on tanks or containers that are used to carry, store or transport certain chemicals.
Containers holding flammable fuels, such as diesel, petrol and natural gas, normally bear warning symbols. So do containers holding toxic chemicals.
These symbols indicate the danger (hazard) likely to be caused by the chemicals they contain if carelessly handled.
When performing experiments in the laboratory, it is important to read the safety signs on chemical containers. This will minimize the chances of causing accidents in the laboratory.
The basic chemical warning signs
Some chemical warning signs are shown here.
The Concept Of Warning Signs
Before you do any experiment in the laboratory, you must know whether the chemical you want to use is toxic, corrosive, flammable, an oxidant, explosive or harmful.
This information helps you to know how to handle the chemicals safely. Proper handling of chemicals helps you avoid unnecessary accidents.
Below is an explanation of some hazard labels represented by the symbols above.
Toxic
Toxic substances are those that can poison you or other people working close to you in the laboratory. These substances can kill within a short time or after a few days.
They should not get into your body through the body orifices (mouth, nose, eyes, ears, etc). They should also not touch your skin. They become even more dangerous when they get into the body.
If these substances touch your skin by accident, wash the skin immediately with plenty of water.
Corrosive
Corrosive substances are chemicals that can burn or corrode (eat away) your skin. They can also corrode wood or metals. A person can become blind if such substances accidentally get into his or her eyes.
If they touch your skin, wash it immediately with a lot of water.
Examples of corrosive substances commonly found in a school laboratory are
- concentrated mineral acids such as sulphuric acid, hydrochloric acid and nitric acid
- concentrated alkalis such as sodium hydroxide, potassium hydroxide and ammonia
Flammable
Flammable chemicals catch fire easily. They should be kept away from flames or fires.
Any kind of spark can set them on fire, whether it comes from welding or from a fire.
When you work with flammable chemicals in the laboratory, all burners must be put off.
These chemicals are usually very volatile. The containers used to carry them must be stoppered immediately after every use.
Examples of flammable chemicals are
- methylated spirit
- ether
- acetone
- methanol
Explosive
Explosive chemicals explode rapidly upon detonation (when they are set on fire or ignited).
Because the reaction is rapid, particles are thrown off at high speed. For this reason, explosive chemicals should not be kept in glass containers. During an explosion, the particles will scatter around and cause serious injuries to people.
Explosive chemicals that can react without external detonation are even more dangerous.
Oxidizing agents
Oxidizing agents are chemicals that make a burning substance burn better and faster. Therefore, they must be kept away from fires, no matter how small the fire is.
An example of an oxidizing agent is oxygen gas.
Harmful or irritant
Harmful substances are those that can impair your health or make you fall sick. They do not normally kill instantly. They have damaging effects after a long exposure to them. However, care must be taken when handling or dealing with them.
Irritating substances cause pain when they touch the body. They are dangerous to health when they stay in contact with the body surface for a long period of time.
The Laboratory
A laboratory is a room or building specially designed for conducting various scientific experiments.
An appropriate school laboratory has the following features
- a room with enough space for carrying out scientific experiments
- a store for keeping laboratory apparatus, chemicals and reagents
- an office where the laboratory technician sits and designs scientific experiments
- enough ventilation to let in fresh air and light
- wide doors and several exits for emergency evacuation in case of an accident
- a wide table in front of the laboratory room, fitted with sinks, for experiment demonstrations by the teacher or technician
