Heat sources
Dakika 8 za kusoma ·
Yaliyomo
Heat Sources
Most chemical reactions require heat to proceed. It is therefore important to have sources of heat in a laboratory for heating various reacting substances.
Sources of heat in a chemistry laboratory may include
- Bunsen burner
- Candle
- Spirit burner
- Kerosene burner (stove)
- Tin lamp (kibatari)
- Charcoal burner
These are burners commonly used in most school laboratories.
Different Heat Sources Which Can Be Used In A Chemistry Laboratory
Bunsen burner
The Bunsen burner is the best of all burners because it is convenient to handle.
Another advantage is that it produces a hot flame. The temperature of the flame is approximately 1000°C.
The temperature can be adjusted easily to produce a non-luminous flame. This flame does not produce much soot.
Spirit burner
The spirit burner can also produce a soot-free flame.
But the flame is not hot enough to effect (produce) some chemical reactions.
Also, the burner is filled with spirit, a substance that is highly flammable.
A candle
A candle can only be used where a chemical reaction does not require much heat.
Its disadvantage is that it produces a lot of soot.
Other burners, though not commonly used, are the electric heater and the gas burner.
The electric heater uses electricity. The gas burner uses a liquefied gas.
The disadvantage of an electric burner is that it cannot be used in rural areas where there is no electricity.
A kerosene burner
A kerosene burner (stove) is also called jiko la mchina in Swahili.
If well adjusted, it can produce a flame hot enough to heat many substances in the laboratory.
It is filled with kerosene, a fuel that is convenient to carry and store.
This fuel does not catch fire easily as compared to spirit. It is also affordable.
It can conveniently be used by schools in the most remote areas where there is no electricity.
If too much heating is required, wire gauze should be placed on top of the burner. This reduces soot and increases the heating temperature to about 1000°C or more.
A charcoal burner
A charcoal burner can also be used in remote areas.
If the kerosene burner is not available, for one reason or another, a charcoal burner can be the best alternative.
The red-hot charcoal on the burner is almost soot-free.
It can produce a high temperature, sufficient to carry out many reactions.
A tin lamp
A tin lamp (kibatari) produces a lot of soot. Even so, it can also be used as a burner in a laboratory, especially in remote areas.
The Functioning Of A Bunsen Burner
Of all the burners we have discussed so far, the Bunsen burner is the most used. Therefore, we are going to discuss its functioning in more detail.
The burner was invented by a German scientist called Robert Bunsen. It was named after him.
The burner uses coal gas. The gas burns with a hot and non-luminous flame when the air holes are open. This is the kind of flame we normally use in the laboratory.
Functions of different parts of the Bunsen burner
- Base: Supports the burner. Because it is heavy, it makes the burner stable when placed on a bench.
- Gas inlet: Lets the gas in from the gas supply.
- Jet: Directs the gas to the barrel.
- Collar: Regulates the amount of air entering the burner. It has air holes that can be turned open or closed. This depends on the kind of flame, and hence the amount of heating, required.
- Air holes: These are small holes on the collar. They allow air to enter the burner.
- Barrel: This is the part of the burner where air (from outside) and gas (from the gas supply) mix and burn.
How to light a Bunsen burner
After knowing the different parts of the Bunsen burner, you should also learn how to light it. This is because careless use of the burner may lead to accidents or wastage of gas.
The correct sequence of steps to light the Bunsen burner is
- Connect the Bunsen burner by a rubber tube to the gas supply.
- Close the air holes.
- Turn the gas tap on to let in sufficient gas.
- Quickly bring a flame to the top of the barrel. You may use a matchstick, a lighter or a wooden splint as the source of flame.
- Turn the collar to adjust the air holes until you get the type of flame you want. You may have the holes completely open.
- Adjust the gas tap until the gas supply is enough to produce a non-luminous flame.
How to put off the flame
After you finish heating a substance, turn the gas tap off. This cuts off the gas supply to the burner.
Disconnect the burner from the gas mains by removing the rubber tube connecting the two.
Then close the air holes.
Do not touch the hot collar with your fingers. Wait until it is cool enough.
Take the Bunsen burner and keep it at the appropriate place.
Types Of Flame
Flames are formed by burning gases or vapours. During burning, heat and light are given out.
For any solid or liquid to burn with a flame, it must first turn into inflammable vapours (gaseous state).
Luminous And Non-Luminous Flames From Different Types Of Flames
A flame can be luminous or non-luminous.
Flames of a candle and of any oil are usually smoky and luminous. Flames of this kind are normally of little use in the laboratory. This is because they are not hot enough and would deposit soot on laboratory apparatus.
Coal gas also burns with a smoky and luminous flame.
With a Bunsen burner, one can produce two types of flames: the luminous flame and the non-luminous flame.
Luminous flame
This type of flame is produced when the air holes of a Bunsen burner are closed.
When the air holes are closed, very little air enters the barrel of the burner. In this case, the flame will be large, unsteady and bright.
The flame will have four main zones, each having a distinct colour.
Luminous Flame: Zones
The luminous flame has four zones.
Inner dark zone
This zone is dark and cool. It contains unburnt gas.
Luminous yellow zone
The gas burns in this zone. The air is not enough, so the burning is incomplete.
Incomplete burning forms tiny carbon particles from the gas. When these particles are white-hot, they give out light. This is the yellow colour we see.
If a cold evaporating dish, porcelain crucible or glass is placed in this zone, it will blacken. The carbon particles (soot) are deposited on it.
Outer zone
This is a non-luminous zone. The gas burns completely here because there is enough air.
There are no carbon particles in this zone, so it does not give out light. Because of this, the zone cannot be seen easily.
Blue zone
There is a rising convectional current. It gives a sufficient supply of air, so the gas burns completely in this zone.
Non-Luminous Flame
When the air holes are fully opened, enough air enters the Bunsen burner barrel. The air mixes well with the coal gas.
Hence, the gas burns much quicker and completely. The flame is smaller and hotter.
There is no white-hot carbon, so no light appears. The flame is therefore non-luminous.
The flame has three distinct zones. Each zone has a different colour.
Cool inner zone
This is a zone of unburnt gas.
Green/blue zone
Part of the gas burns in this zone. There is not enough air to burn all the gas completely. However, no carbon is formed.
The hottest part of the flame is at the tip of this zone.
Major Differences Between Luminous And Non-Luminous Flames
Non-luminous flame
- It is formed when the air holes are open.
- It is very noisy.
- It has three zones.
- It forms no smoke or soot on apparatus.
- It is blue and almost invisible.
- It is a very hot flame.
- It is not bright.
- It is a triangular flame.
Luminous flame
- It is formed when the air holes are closed.
- It is silent or calm.
- It has four zones.
- It forms a lot of smoke or soot on apparatus.
- It is bright yellow and clearly visible.
- It is not a hot flame.
- It is very bright.
- It is a wave-like flame.
Uses Of Flames
Flames are used for different purposes. Some uses of flames are the following
Production of heat for heating substances in the laboratory
A non-luminous flame is used here. It produces much heat.
For reactions that need little heat, a luminous flame can be used. It is not very hot.
Flame tests for elements
A flame test is one of the preliminary tests normally used in the chemical analysis of some elements. It helps to identify an element.
When some elements are strongly heated, they produce characteristic flame colours. These colours distinguish the elements from one another.
A non-luminous flame is often used.
Production of light
Flames produce light that can light a dark room. Therefore, an experiment that involves heating can even be done in the dark.
The same flame gives heat as well as light. A luminous flame is used here.
Examples of heat sources whose flames may be used for lighting are
- hurricane lamp
- tin lamp
- spirit lamp
- candle
Cooking
A non-luminous flame gives a hot flame and produces no soot. So it can be used for cooking food.
Gas cookers, gas stoves and kerosene stoves usually produce such flames.
Welding
A non-luminous flame is suitable for welding because it is very hot.
In most welding operations, oxyacetylene gas is used. It is a mixture of oxygen and ethyne.
When burned, the gas produces a flame hot enough to cut or melt metal.
